Origami paper glider: DC-3 model

The DC-3 is one of the most famous aircraft in the history of civil aviation, and its silhouette is still recognizable today. The name of this fold comes from the original diagram, and let's say it right away: the resemblance to the real DC-3 is distant. The principle, however, is correct: wide wings set back, outlined tail, and a long fuselage that shifts the weight forward.

This is the longest model in this section: thirty-four steps, and a rare peculiarity in origami. The fuselage is not folded, it is cut from the sheet itself, in step 24: everything therefore comes from a single sheet, with nothing added. It is documented differently as well. These are not diagrams but photographs, without the usual lines or arrows: you have to read two photos at a time, one of the gesture and one of the result. Take your time with the first nine, as they build the base on which everything else rests.

In brief

  • Paper: a single ordinary rectangular sheet
  • Number of steps: 34
  • Folds used: valley fold, mountain fold, crushed fold
  • Cutting: the fuselage tab (step 24) and the two rear ailerons (step 26)
  • Difficulty: advanced
  • Duration: 20 to 30 minutes
  • Flight: long, slow glide; gentle, horizontal launch
Finished DC-3 paper airplane model, fuselage slotted in

The folds used

This model is not described by a diagram but by photographs: there are therefore no dotted lines or arrows to interpret. The gestures, however, remain the same as everywhere else: valley fold, mountain fold, and especially the crushed fold in steps 8 and 9. If these names mean nothing to you, the page basic origami folds shows them one by one, and the origami symbols will serve you for all other models on the site. One caveat, however: this fold requires cutting, which origami generally forbids. Purists will tell you that it is therefore not strictly origami.

The folding steps

Step 1: place the sheet — DC-3 paper airplane origami

Step 1: Place the sheet

An ordinary rectangular sheet, placed vertically in front of you. Nothing else is needed: everything, including the fuselage, will come from this single sheet. Work on a hard table, as this model requires well-pressed folds.

Step 2: the first diagonal — DC-3 paper airplane origami

Step 2: The first diagonal

Bring the top corner to the opposite side edge so that the top edge lies exactly along the side. The fold formed is at 45°. Adjust both edges against each other before pressing: the entire subsequent construction depends on this diagonal.

Step 3: mark the fold with your nail — DC-3 paper airplane origami

Step 3: Mark the fold with your nail

Run your nail along the fold from one end to the other, pressing firmly. A loose fold here will cause problems in step 8 when the paper needs to refold on its own.

Step 4: unfold — DC-3 paper airplane origami

Step 4: Unfold

Lift the flap and lay the sheet flat again. Only the crease remains: a clear diagonal across the top part, which outlines the square at the top of the sheet.

Step 5: the second diagonal — DC-3 paper airplane origami

Step 5: The second diagonal

Repeat on the other side: this time, the opposite corner is laid along the edge. The motion is the same, mirrored.

Step 6: mark, then unfold — DC-3 paper airplane origami

Step 6: Mark, then unfold

Run your nail along the entire length as before, then unfold again.

Step 7: the two crossed diagonals — DC-3 paper airplane origami

Step 7: The two crossed diagonals

The flat sheet now shows an X in its upper part, with the two diagonals intersecting at the center of the square. This is the classic preparation for a crushed fold.

Step 8: bring the sides together — DC-3 paper airplane origami

Step 8: Bring the sides together

Hold the sheet by its two sides at the level of the X and push them toward each other. The paper folds by itself along the creases: the top lifts and closes into a point.

Step 9: flatten the base — DC-3 paper airplane origami

Step 9: Flatten the base

Lay everything flat on the table and press down. The top of the sheet has become a double triangle, resting on the rest of the sheet, which remains flat. This is the starting base for the model.

Step 10: open the first flap — DC-3 paper airplane origami

Step 10: Open the first flap

Lift the top layer of the triangle on the left side and spread it slightly. Do not fold it back yet: open it so you can lay it in the right place.

Step 11: lay the flap down — DC-3 paper airplane origami

Step 11: Lay the flap down

Bring this flap to the top of the triangle and lay it flat. A clean edge appears along the central axis.

Step 12: the second flap — DC-3 paper airplane origami

Step 12: The second flap

Do exactly the same on the other side. The two flaps meet at the axis, and the triangle takes the shape of a diamond.

Step 13: the small flap at the top — DC-3 paper airplane origami

Step 13: The small flap at the top

Fold the small point that protrudes at the top, laying it on the diamond.

Step 14: flatten the flap — DC-3 paper airplane origami

Step 14: Flatten the flap

Press it against the diamond, carefully following the edge. The resulting triangle should have two equal sides.

Step 15: the same flap on the other side — DC-3 paper airplane origami

Step 15: The same flap on the other side

Repeat steps 13 and 14 identically on the other side. The model becomes symmetrical again.

Step 16: lift a point — DC-3 paper airplane origami

Step 16: Lift a point

Lift the left point and pinch it along its entire length to give it body.

Step 17: lay the point down — DC-3 paper airplane origami

Step 17: Lay the point down

Fold it inward and press. It fits against the axis.

Step 18: the inner fold — DC-3 paper airplane origami

Step 18: The inner fold

Fold the top of the diamond on the same side to create an inner fold: the paper tucks between the layers instead of lying on top.

Step 19: repeat on the other side — DC-3 paper airplane origami

Step 19: Repeat on the other side

Repeat steps 16 to 18 on the other side. Both halves must mirror each other exactly, otherwise the plane will veer off course.

Step 20: the DC-3 nose — DC-3 paper airplane origami

Step 20: The DC-3 nose

Fold the nose of the plane at the level of the inner folds you just made. This fold gives the model its wide, short nose, characteristic of the DC-3.

Step 21: the resulting profile — DC-3 paper airplane origami

Step 21: The resulting profile

Viewed from three-quarters, the model has a flat part (the wings) and a central raised V-shape. This raised part is key: it is the beam that prevents the plane from folding in flight.

Step 22: form the fold — DC-3 paper airplane origami

Step 22: Form the fold

Form the fold by refolding the rear rectangle to mark the line along its entire length.

Step 23: moisten the fold — DC-3 paper airplane origami

Step 23: Moisten the fold

Run your tongue along the fold. The moistened paper tears cleanly and straight, without fraying: this allows the tab to be cleanly detached in the next step.

Step 24: detach the fuselage — DC-3 paper airplane origami

Step 24: Detach the fuselage

Detach the tab along the moistened fold. This will become the fuselage.

Step 25: fold the fuselage — DC-3 paper airplane origami

Step 25: Fold the fuselage

Fold the tab in half lengthwise: a single fold is enough to turn it into a rigid profile. Press it well, as this stiffness will hold the entire front of the plane.

Step 26: the finished profile — DC-3 paper airplane origami

Step 26: The rear ailerons

Make two small notches at the rear of the model and unfold the tabs thus released: these are the ailerons. Two light cuts, nothing more.

Step 27: pick up the body of the plane — DC-3 paper airplane origami

Step 27: Pick up the body of the plane

Pick up the body of the plane and open it slightly to reveal its two wings.

Step 28: create volume — DC-3 paper airplane origami

Step 28: Mark the wing fold

Mark the wing fold from the nose to the rear, pressing along its entire length. This determines the angle of both wings and thus how the plane will fly.

Step 29: adjust the axis — DC-3 paper airplane origami

Step 29: Adjust the wing plane

Pinch the central axis between your thumb and index finger along its entire length to bring both wings exactly into the same plane.

Step 30: front view — DC-3 paper airplane origami

Step 30: The wings seen from the front

From the front, both wings must form the same angle. This is the quickest and most reliable check.

Step 31: top view — DC-3 paper airplane origami

Step 31: The wingtip ailerons

Lift the small ailerons at the wingtips on each side. These prevent the aircraft from rolling from side to side in flight.

Step 32: insert the fuselage — DC-3 paper airplane origami

Step 32: Slot in the fuselage

Slot the profile into the fold at the nose of the plane and push it in until it holds on its own. It should extend well beyond: this overhang places the center of gravity in front of the wings.

Step 33: assembly complete — DC-3 paper airplane origami

Step 33: The finished plane

The fuselage is in place, and the plane holds together as one piece. Make sure it is properly aligned: a crooked fuselage will cause the aircraft to turn as soon as it is launched.

Step 34: unfold the nose triangle to form the landing gear — DC-3 paper airplane origami

Step 34: The landing gear

Unfold the inner triangle of the nose: it hangs below the aircraft and forms the landing gear. It's a small detail, but it allows the plane to be placed on a table without tipping forward onto its nose.

DC-3 paper airplane model held against the sky, ready to be launched

The launch

Hold the plane by the fuselage, just behind the nose, and launch gently, keeping it horizontal. It will glide long and slow, provided you don't try to throw it hard. This is typical of models with a large wing surface.

网上汉语 · learn-chinese.online

Chinese course

Level 1 · Beginner
学
中
文

A clear, structured method to get started in Mandarin.

✓Units 1 to 5: freeLessons, exercises and assessments, full access.
🔓Units 6 to 10: open accessThe course to read, without exercises or assessments. No login needed.
Start for freeImmediate access to level 1

The HanWen Shop

Every item tells a story of China!

Hand-engraved personalised Chinese seal

Personalised gift

Chinese names, personalised seals and bespoke creations: made just for you.

Discover
Red Hanfu embroidered with dragons

Hanfu – Elegance from China

Discover the beauty of traditional Chinese clothing and give the gift of a journey through the dynasties.

Discover
Chinese calligraphy brushes

Chinese art supplies

Brushes, Xuan paper, ink and calligraphy: gifts for creative minds.

Discover
Golden phoenix crown adorned with pearls

Jewellery that tells a story

Pearls, lucky charm pendants and hairpins: delicate, thoughtful gifts to give.

Discover
Chopstick gift set with panda chopstick rests

Traditional gifts

Gift ideas in the colours of China for the festive season.

Discover
Chinese silk and bamboo fan

Fan & Parasol

They bring a unique artistic touch to your everyday life.

Discover
  • Free shipping: France from €69.90 | EU from €99.90 | Rest of Europe from €129.90
  • Original gifts: shipped directly from France. 🇫🇷
  • Unique creations: personalised and handmade, just for you.